PP Automatic strapping machine

YH-1250 automatic strapping machine

1. Power supply: AC220V, 50/60Hz, 1.0 KW

2. Dimensions: L1520mm×W680mm×H2000mm

3. Strapping specification: Standard frame size: width 1250mm× height 500mm

4. Workbench height: 850mm

5. Load-bearing capacity: 80kg

6. Binding speed: ≤30 channels /min

7. Binding force: 0-45kg

8. Binding tape specifications:

Poly (propylene), 5mm, 6mm wide, 0.5mm ~ 0.8mm thick

9. Bonding method: hot melt method, bottom bonding, bonding surface ≥90%, bonding position deviation ≤2mm.

10. Machine weight: 1200kg

11. Noise: under working environment, noise ≤75dB (A)

12. Environmental conditions: humidity ≤90%, temperature 0-40℃

Electrical configuration:

(1) Using PLC control, so that the running time is accurate to 1 millisecond, but also can be adjusted on site; Stable and reliable, low failure rate. The similar products are controlled by circuit board or single chip microcomputer, which is easy to be affected by the external environment and has low life;

(2) Electrical appliances: push-button switch: Nino; PLC controller: Delta; Relay: Omron;

Mechanical arrangement

(1) Japan's latest mechanical structure, no refueling maintenance, to ensure superior mechanical performance;

(2) Four packaging operation modes, manual, continuous play, ball switch, foot switch, for you to solve a variety of packaging;

(3) The frame is made of aluminum alloy profile, which is formed once and should not be bent to ensure the strength; And easy to disassemble, can be customized according to customer requirements;

(4) There is a brush on the frame to ensure that the packing belt does not deviate and reduce errors;

(5) There are three knives, the middle knife, the front knife, the back knife, the blade is made of measuring steel (manganese 13 material), to ensure the strength and hardness of the knife body, more wear-resistant, longer life; The tool body and the tool head can be disassembled, both sides of the tool head can be used, only need to replace the tool head after wear, saving cost;

(6) The hot head is made of special stainless steel (copper alloy) material, which is not suitable for aging deformation, and the principle of short circuit for heating the month, with the operation mode of low voltage and high current, the life ratio is the same length; With high current and low current, mica sheet heating wire is easy to oxidize and age;

(7) T-groove and skateboard are made of steel, and there is a reverse mouth under the skateboard, making the skateboard more durable and longer life;

(8) Nitriding is used for the high wear cassette block, so that its life is 1.5 times longer than the original;

(9) Add steel plate under the unique swing rod device to ensure that the large swing rod (under the device) should not be worn under the use;

(10) The main motor and reducer are connected, reduce the parts, so that the transmission is more stable, and the peer uses the belt drive;

(11) The main motor is used to drive the main shaft, and the rolling friction between the CAM and the bearing is used between the main shaft and the tool holder, which has small friction and long life, and is not a wearing part;

(12) Voltage is widely used

(13) The harsh environment can also ensure excellent characteristics, the temperature of -15℃--15℃. Humidity 10-90% and heavy dust.

(14) According to customer requirements, the packaging can achieve smoke-free emissions;

Increase efficiency:

The tying speed is the fastest in the country, 2.2 seconds/dao;

Reduce costs:

The requirements for the packing belt are wide, the thickness (0.55-1.2) mm, the width (9-15) mm, the same weight of the belt we can do very thin, longer, more packaging; Lower cost of packaging compared to existing machines on the market.